Quick answer
Pool table moving is the work of taking a pool table apart into its slate sections, rails and frame, moving each part, and rebuilding the table level and re-covered at the new address.
A slate table is not carried whole. It is built from heavy sections on a frame, and it only plays true when the sections are leveled again. California’s tariff treats pool tables as unusual articles that a mover disassembles only on request.
Quick facts
The key facts about Pool Table Moving, with sources:
- What it involves
- Disassembly, transport of slate, frame, rails and cloth, then reassembly and leveling 2
- Slate thickness, WPA event standard
- At least 1 inch 1
- Slate joints after leveling, WPA event standard
- In the same plane within 0.005 inch 1
- Slate layout, tournament tables
- Three pieces of equal size on a wooden frame 1
- Published weight, two Brunswick 7-foot tables
- 589 pounds (Glenwood) and 682 pounds (Sanibel) 3
- California tariff treatment
- Pool tables are “unusual articles”; disassembly is done on request and charged under the hourly item 7
- Estimated volume, California tariff table
- 40 cubic feet for a pool table 7
Key takeaways
- A slate pool table is moved in parts. Brunswick’s installation manual shows a three-piece slate set on a frame, rails and cloth 2.
- Leveling is the real work. The WPA event standard asks for slate joints in the same plane within 0.005 inch after leveling and shimming 1.
- Tell the mover the table is coming. California’s tariff does not include disassembly of pool tables in its basic rates, and a mover does it only on request 7.
- No source we loaded gives a slate-only weight, so ask for the maker’s figure. Brunswick’s listing prints 589 and 682 pounds for two 7-foot tables, though its metric figures on the same page do not match, so confirm with the maker 3.
- Slate is heavy and brittle, so use a trained crew and equipment for the sections 9.
Pool table moving in plain English
A pool table is a flat, heavy stone bed in a wooden box. The stone is slate, cut into sections. The slate sits on a base frame, and a cloth is stretched over it.
Rails with rubber cushions and pockets are bolted around the edge. Brunswick’s installation manual for five of its models builds one in that order: legs and baseframe, then slate, then cloth, then rails 2.
Moving one therefore means taking it apart. The slate comes off the frame, the cloth and rails come off, and each piece travels on its own. At the new home, the table is built again, and the slate must be leveled until the surface plays true.
Why does it matter that the table is level? The World Pool-Billiard Association (WPA) sets event standards for flatness.
The slate must hold a flat surface to within 0.020 inch along the length and 0.010 inch across the width, and the slate joints must lie in the same plane within 0.005 inch after leveling and shimming 1.
Those are tournament figures. The WPA says its specifications do not necessarily apply to tables made for home use 1. They still show how fine the tolerances are for a table meant to play well.
How a slate table is rebuilt, step by step
The order below comes from Brunswick’s installation manual for its Allenton, Shorewood, Danbury, Tahoe and Amherst tables (September 2006). Your table may differ. Use the maker’s own manual or a trained installer for your model 2.
- Level the baseframe first. With a carpenter’s level, find the highest corner of the baseframe, then place the shims supplied with the table under the other legs. The top surfaces must be flush 2.
- Place the center slate. Set the center section on the frame, square with it, with an equal overhang on both sides 2.
- Place the end slates. Position the two end sections, and check that the overhang is equal all around 2.
- Fasten and wedge the ends. Fasten the end slates, then drive the wooden slate wedges between the frame and the slate while checking with a precision level 2.
- Shim the center. Shim the center section so the joints are flush, then screw it down 2.
- Fill the joints. Brunswick says to fill slate joints with fast-setting putty, beeswax or slate joint wax, then lightly sand or scrape across the joint 2.
- Cover, then add rails. Stretch and staple the bed cloth, then attach the rails 2.
- Level the frameShim legs, check with a carpenter’s level
- Set the slateCenter section, then both end sections
- Wedge and shimBring all three pieces level and flush
- Fill the jointsPutty, beeswax or slate joint wax
- Cloth and railsStretch the cloth, then bolt the rails on
The order follows Brunswick’s installation manual for its pocket billiard tables. Source: [2]
The parts that travel, and what each needs
| Part | What it is | What it needs when moved |
|---|---|---|
| Slate sections | The playing bed. WPA says tournament tables use three pieces of equal size on a wooden frame at least ¾ inch thick 1 | The most careful handling. Slate is heavy, and the joints must be re-leveled 12 |
| Baseframe and legs | The structure the slate sits on. Brunswick levels it first with shims 2 | Hardware kept together and labeled so the frame goes back the same way (our advice, not a maker’s rule) |
| Cloth | The bed cloth is tacked or stapled to the wooden slate frame 2. WPA says the cloth is fastened to the wooden slate liner 1 | It can stretch, and Brunswick notes wrinkles can form at the pockets and need re-tacking 2 |
| Rails and cushions | Brunswick’s manual has the installer locate eighteen rail attach holes and cut the cloth around them 2 | Bolts counted and bagged; the rail finish is easy to scratch |
| Pockets and liners | Cut into the slate, with strips of cloth glued to the cutouts 2 | Check them for damage after the move |
Home tables are not tournament tables
The WPA specification is written for WPA events, and it says it does not necessarily apply to tables made for home use 1. Brunswick lists 1-inch slate on its home tables 3. Use the WPA figures to understand why leveling matters, not as a warranty standard for your table.
Example: how small the tolerances are, and how much room a table needs
The first table lists the WPA event tolerances for a slate table in inches and in thousandths of an inch.
The second applies the WPA’s tournament spacing rule to the overall size of two Brunswick home tables. The spacing rule is for competitions, so a home room may use less.
The room sizes are HyreMover arithmetic, not a standard for home play.
| Measure | Source figure | In thousandths of an inch |
|---|---|---|
| Slate joints in the same plane | Within 0.005 inch after leveling and shimming 1 | 5 |
| Flatness across the width | Within 0.010 inch 1 | 10 |
| Flatness along the length | Within 0.020 inch 1 | 20 |
| Extra deflection with a 200-pound load at the center | No more than 0.030 inch 1 | 30 |
Now the room. The WPA requires at least 6 feet (72 inches) between the outside edge of the rail and any obstacle in competitions 1.
Brunswick lists the Glenwood 7-foot table at 86.5 by 48.5 inches and the Sanibel at 90 by 52 inches 3.
Adding 72 inches on each side gives about 230.5 by 192.5 inches (19 by 16 feet) for the Glenwood and 234 by 196 inches (19.5 by 16.3 feet) for the Sanibel. Few homes have that.
The point is to measure the new room before the table moves, so you do not find out it does not fit once the slate is leveled. The truck size tool can help check the load.
Where pool table moving appears: the survey, the tariff and the inventory
A pool table is usually named at the survey as a specialty item. Say it is slate, name the maker if you know it, and give the table size. The specialty moving page explains how these items are declared.
In California’s Maximum Rate Tariff 4, Item 172 says basic distance rates do not include assembling or disassembling “unusual articles found inside of buildings,” and it names pool tables in its examples.
On request, the mover disassembles or reassembles such articles at the hourly rates in Item 320. You supply any new hardware at reassembly 7. That is one state’s rule, so ask your own mover how it lists the work.
On the estimate and inventory, the table may appear as a piece with its own line.
The same tariff’s Table of Measurement and Estimate lists 40 cubic feet for a pool table and 20 for a ping pong table 7. That is an estimating convention, not the real size. Read moving estimates to see how volume turns into a quote.
Hiring a crew to move a slate table, compared with doing it yourself
Where a trained crew helps
- Slate sections are heavy. NIOSH guidance says to use mechanical devices for heavy loads and that team lifting is only a temporary measure 9.
- The rebuild needs a carpenter’s level, shims and wedges, as Brunswick’s manual shows 2.
- A crew can note the table’s condition on the inventory before it is taken apart.
- Some makers offer delivery and installation by authorized installers for new tables 3.
What it costs or does not fix
Limits: what a move cannot give you
A move cannot make an old table new. If the cloth is worn or the cushions are tired, taking the table apart does not fix them.
Brunswick’s manual also warns that cloth can stretch and leave wrinkles at the pockets, so it may need to be pulled taut and re-tacked 2. No source we loaded says a move always needs new cloth.
It also cannot guarantee a level floor. The table is leveled with shims on the legs and wedges under the slate 2. A badly sloping or soft floor is the room’s problem, not the table’s. The WPA says a table’s construction should keep it stable and level under all conditions of play 1.
Last, a move cannot decide the claim for you. On an interstate move, Appendix A says the mover is legally liable for loss or damage in transit, subject to the valuation level 4.
Under released value, the mover is liable for no more than 60 cents per pound, per article 4. A slate section that cracks is unlikely to be made whole by that formula, so ask about full value protection. This page is not legal advice.
Slate is heavy and brittle
Do not lift slate sections without trained help and equipment. NIOSH guidance says to test a load for stability and weight, use mechanical devices for heavy loads, and avoid stairs when carrying 9.
Keep hands clear of edges, and never stand below a section on a stair. A cracked slate cannot be treated like a scratched table leg.
What drives the cost of moving a pool table
We do not publish prices. A pool table quote rests on a few things you can ask about. The first is the work: disassembly, transport, reassembly, leveling and re-covering are separate tasks.
The second is the table: its size and the number of slate pieces. The third is the route: stairs, long carries and tight turns at both homes.
Under federal interstate rules, extras such as stair carries show up as accessorial services, and Appendix A names a flight charge as an additional charge for carrying items up or down stairs 4.
Impracticable operations, which need specialized equipment or extra labor, may also be charged, up to 15 percent of other charges due at delivery 4. California’s tariff bills table disassembly at the hourly item 7.
Parts add to the bill. Cloth, wax and new hardware are materials, and a third party who relevels or re-covers the table is billed through the mover as an advanced charge if the mover arranges it 47.
No source we loaded gives a lifespan or warranty for a move, so we offer none. See the cost guide to compare quotes line by line.
Arranging a pool table move: survey, parts, route and final spot
The rules that most often apply are the building’s: elevator bookings, stair and hallway limits, and insurance certificates. Ask early.
- Weeks ahead: name the table at the survey, with maker, size and slate type 5.
- Weeks ahead: ask whether the mover disassembles and reassembles the table, or sends a specialist, and who levels it.
- Before the day: photograph the table, including cloth, rails and cushions, and any chips in the slate.
- Before the day: measure the stairs and turns against the width of the slate, not the width of the table.
- Moving day: keep every screw, bolt and wedge in labeled bags with the piece it belongs to.
- Delivery day: choose the final spot first, then build and level the table there. Moving a leveled table is a second job.
- After delivery: check the surface, joints and cloth, and note damage before the crew leaves. See moving damage claim.
After the move: check the table before you play
- Check level. Use a carpenter’s level on the bed. Brunswick’s manual levels the baseframe first, then the slate 2.
- Check the joints. They should be flush and filled. Brunswick names putty, beeswax and slate joint wax as fillers 2.
- Check the cloth. Look for wrinkles at the pockets. Brunswick says to retack taut cloth if it has stretched 2.
- Check the rails. Make sure all bolts are in and tight. Brunswick’s manual shows eighteen attach holes 2.
- Keep the cloth clean. The WPA recommends a soft horsehair brush, a billiard-fabric cleaner or a brushless vacuum, and says brushes that shed bristles are not recommended 1.
- Keep your bags. Keep the spare hardware and the manual with the table for the next move.
Pool table red flags: unnamed table, cracked slate, nobody to level it
- A quote that never mentions the table or says “we will see on the day.” A new item on moving day is a change to the estimate 6.
- A crew that cannot say who levels the slate or what it does with the wedges and shims 2.
- A plan to carry slate down stairs with friends. Stop and hire help 9.
- A cracked or chipped section found at delivery. Note it on the paperwork right away.
- A table that rolls the ball to one side after reassembly. It needs leveling again.
- A mover that pushes released value without explaining the 60-cent rule 4.
For hazards across the whole day, read moving day safety.
Rules and standards: what binds, and what only advises
Federal, interstate moves. 49 CFR Part 375 covers household goods moved across state lines.
Appendix A to Part 375 sets full value protection as the level a shipment moves under unless the shipper waives it in writing, and released value at no more than 60 cents per pound, per article 4.
A mover must base an estimate on a physical survey, unless you waive one in writing 5.
If you tender goods not listed on a binding estimate, the mover is not required to honor it 6.
State, moves inside one state. The federal rules above do not bind a move that stays in one state. California’s Maximum Rate Tariff 4, effective January 1, 2023, is one example. Item 172 lists pool tables among unusual articles whose disassembly is done on request 7. Other states differ.
Industry standard, advisory. The WPA Recommended Equipment Specifications (effective November 2001) set tournament figures for slate thickness and flatness. The WPA says they do not necessarily apply to home tables 1. They are not a rule for movers.
Valuation is not insurance. It is the mover’s own liability under its tariff, and third-party cargo insurance is a separate product 4. See valuation and insurance.
Pool table moving compared with neighboring terms
| Term | What it covers | How it differs |
|---|---|---|
| Pool table moving | Disassembly, transport and level rebuild of a slate table | This page |
| Furniture disassembly and reassembly | Taking furniture apart and rebuilding it | A pool table adds slate, leveling and cloth work |
| Piano moving | Specialty crew for a heavy, tuned instrument | Weight is similar; leveling and humidity differ |
| Safe moving | Dense, often bolted containers | One mass, not several heavy sections |
| Moving accessorial services | Extra services such as flights and carries | A billing category that can include table work |
| Moving heavy furniture | Technique for dense household pieces | A table’s slate is far heavier than a dresser |
Pool table moving myths
- Myth A pool table can be carried whole.
- Reality Brunswick’s manual shows a table built from legs, baseframe, three slate sections, cloth and rails, assembled in order 2.
- Myth If the table is bolted together, it is level.
- Reality Brunswick levels the baseframe with shims, then wedges and shims each slate section, and rechecks 2.
- Myth A small tilt does not matter.
- Reality The WPA’s event standard keeps slate joints within 0.005 inch of one plane 1.
- Myth The mover’s coverage pays for a cracked slate.
- Reality Under released value the limit is 60 cents per pound, per article 4. Full value protection repairs or replaces 4.
- Myth A mover always takes the table apart for free.
- Reality In California’s tariff, disassembly of pool tables is done on request and charged at the hourly item 7.
Where the local variable is the state’s moving rules
Inside one state, the state decides how a mover handles a pool table.
California’s Bureau of Household Goods and Services publishes Maximum Rate Tariff 4, which names pool tables among unusual articles 7.
Texas’s Smart Mover guide says Texas law requires a mover operating within the state to be licensed by both the TxDMV and the U.S. DOT, and that accessory charges should be explained in the mover’s tariff 8.
Other states differ, so check your state’s agency before you assume a rule.
When a slate table changes your plan, and the next step
Pool table moving matters whenever a table is part of a move, because it cannot be treated as a normal piece of furniture. It matters most when the route has stairs, when the table is a high-grade slate model, or when you want it playing true on day one.
Your next step is short. Find the maker’s manual or the model name, measure the slate and the route, and put the table on the survey.
Ask who disassembles it, who levels it and who recovers it. Then compare crews through the choosing a moving company guide, and read the high-value item declaration page if the table is a collector’s piece.
Questions about Pool Table Moving
Can I move a pool table myself?
It is risky. A slate table is built from heavy sections that must be taken apart and leveled again. NIOSH guidance says to use mechanical devices for heavy loads and to avoid stairs when carrying.
A trained crew or the maker’s installer is the safer choice for slate. Ask the maker or a trained installer how your model comes apart, and check the weight of the slate sections first.
Do movers take a pool table apart?
Some do, on request. California’s tariff says its basic distance rates do not include disassembling unusual articles such as pool tables, and that the mover will do it on request at the hourly item.
Ask your own mover whether it does the work or uses a specialist. Ask who levels the slate and who recovers the table, since those are separate tasks.
How heavy is a pool table?
It depends on the table. Brunswick’s listing prints 589 pounds for its Glenwood 7-foot table and 682 pounds for its Sanibel 7-foot, but the kilogram figures beside them do not match, and the listing does not say what is included. No source we loaded gives a slate-only weight. Ask the maker for your model.
Does a pool table need to be re-leveled after a move?
Yes, in effect, because it is rebuilt. Brunswick’s manual levels the baseframe, then wedges and shims each slate section with a precision level.
The WPA event standard asks for slate joints in one plane within 0.005 inch after leveling and shimming.
Brunswick’s own steps put leveling the baseframe before the slate goes on, so the order matters.
Do I need new felt when I move a pool table?
Not always. No source we loaded says a move requires new cloth. Brunswick notes that cloth can stretch and leave wrinkles at the pockets, and can be re-tacked taut. A technician can tell you whether yours needs recovering. Ask a technician to check the bed cloth at the pockets and rails after reassembly.
What is the slate in a pool table?
It is the stone playing bed under the cloth. The WPA event standard requires slate at least 1 inch thick, and tournament tables use three pieces of equal size on a wooden frame. Brunswick’s Allenton listing shows 1-inch slate. Slate joints are filled and leveled after the sections are in place, as Brunswick’s manual shows.
Will the mover’s valuation cover the table?
It covers it at the level you choose. On an interstate move, full value protection is the default unless you waive it in writing, and released value is no more than 60 cents per pound, per article.
Valuation is the mover’s liability, not insurance. Slate that cracks is unlikely to be made whole by the weight formula, so ask about full value protection.
How should I prepare a pool table for moving?
Photograph it, find the maker’s manual, and bag every screw, bolt and wedge with a label. Measure the stairs and turns against the slate sections. Tell the estimator at the survey, so the table appears on the written estimate. Keep the maker’s manual and spare hardware with the table for the next move.
How much room does a pool table need?
More than the table itself. The WPA requires at least 6 feet between a table’s rail edge and any obstacle in competitions. Homes often use less, but measure the new room before the move.
Brunswick lists a 7-foot Sanibel at 90 by 52 inches. A home room often has less space, so measure before you decide where the table will stand.
Sources
- World Pool-Billiard Association, Recommended Equipment Specifications (effective November 2001), retrieved .
- Brunswick, Pocket Billiard Table Installation Manual for the Allenton, Shorewood, Danbury, Tahoe and Amherst models (publication 51-904768-003, September 2006), retrieved .
- Brunswick Billiards, Allenton 7-foot pool table product page (listing of 7-foot tables with slate, size and weight), retrieved .
- Appendix A to 49 CFR Part 375, Your Rights and Responsibilities When You Move (read at Cornell LII), retrieved .
- 49 CFR 375.401, Must I estimate charges? (read at Cornell LII), retrieved .
- 49 CFR 375.403, How must I provide a binding estimate? (read at Cornell LII), retrieved .
- California Bureau of Household Goods and Services, Maximum Rate Tariff 4 (effective January 1, 2023), Item 172 and the Table of Measurements and Estimate (Item 410), retrieved .
- Texas Department of Motor Vehicles, Smart Buyer Series: Smart Mover (January 2025), retrieved .
- NIOSH, Cal/OSHA and MHI, Ergonomic Guidelines for Manual Material Handling (DHHS (NIOSH) Publication 2007-131), retrieved .
Expert review
Written by the HyreMover Research Desk. Not yet reviewed by an outside expert. We say so rather than imply a review that has not happened; see our editorial policy.
How the numbers were checked: Assembly order and leveling steps read in the Brunswick installation manual (September 2006); slate tolerances, spacing and cloth guidance read in the WPA Recommended Equipment Specifications; table sizes, weights and slate thickness read on Brunswick’s product page.
Federal rules read at Cornell LII (Appendix A to 49 CFR Part 375, 375.401, 375.403); California treatment read in Maximum Rate Tariff 4 Item 172 and the Item 410 table; Texas licensing read in the TxDMV Smart Mover guide; handling guidance read in the NIOSH 2007-131 booklet, all on 2026-10-14 and 2026-10-15.
Brunswick’s product page prints metric weights that do not match its pound weights, so the pound figures are reported as printed and flagged. The room-size figures are HyreMover arithmetic on the WPA tournament spacing rule and Brunswick’s sizes.
No slate weight is given because no loaded source prints one. This is not legal or safety advice.
Suggest a correction. We fix errors and say what changed.